BoLS logo Tabletop, RPGs & Pop Culture
Advertisement

Warlord: Winter Whitewashing 101

7 Minute Read
Dec 26 2015
Advertisement

SingletonWhitewashComplete600x328

Warlord Games delivers a great Hobby Article on how to apply some great Winter Whitewash to your Bolt Action vehicles!

Warlord Games’ Winter Whitewashing tutorial is perfect for applying that little extra to your Bolt Action tanks and vehicles. The best part is this technique is super simple and can be applied to ANY modeling system or vehicle.

via Warlord Games

With the recent release of our Winter German and Winter American Bolt Action forces, we allied with the ever-eager-to-help Andy Singleton of Volley Fire Painting Services to give the low-down on how to add the distinct Winter White Wash look to your tanks and vehicles…

Whitewashing was a tactic employed by the Germans and Soviets on the Eastern Front, as well as the German and American forces on the Western Front – so Andy’s tutorial focuses on the rather splendid Tiger, although it’s a technique which can be applied to the vehicles of any nation!

 

This is my simple guide to applying winter whitewash. You can get various special chipping effect solutions and paint fancy effects, however some simple gloss varnish and household salt can get you a great looking weathered winter finish. I’ve used an airbrush to paint my Tiger, however this is not required, you can also apply the white using a brush, or even use some packing foam that comes in blister packs if you want to get a really rough and weathered finish!

I’m using a plastic Tiger tank here, but the techniques work for any vehicle from any army, and can even be used for things like helmets and ammunition boxes. Anything that would get a winter finish!

Advertisement

Winter whitewash was applied as a temporary paint finish to vehicles serving in snowy conditions to provide a semblance of camouflage. The paint was applied in a fairly haphazard fashion and tended to be water soluble too, so become worn and streaky very quickly. This can be a daunting looking finish to attempt, but can also be spectacular. Through the next 7 steps I’ll show you how it can be done!

 

Step 1 – Build and Prime

Singleton Whitewash (1)

Fairly self explanatory this – build the vehicle so that it is mostly complete, but leave off the tracks. You could leave the wheels off until later if you wanted. I just glued mine on as I wanted to get a feel for how the model looked, and didn’t want to risk losing them! I used a grey car primer, but use whatever you normally like. The model will be getting a fairly hard treatment though so the primer does need to be something tough – Army Painter Colour Primers are ideal!

 

Step 2 – Paint Base Colour

Singleton Whitewash (2)

At this stage paint the vehicle whatever colour it spends most of its time, for a German vehicle post 1943 such as my Tiger this would normally be a sand yellow colour, and would generally have a distruptive pattern of green and brown, though this camouflage wasn’t always present. I like plain sand yellow vehicles so I left mine camouflage free. For my Tiger, I used Vallejo Middlestone, however if you use the Games Workshop paint range Zandri Dust is a good colour.

Advertisement

 

Step 3 – Detailing

Singleton Whitewash (3)

At this stage I pick out all the things like tools, tow cables, spare tracks etc. These would normally be whitewashed over on the real vehicles, so painting them before the white goes on gives you a nice effect. I also use this stage to apply any transfers to the vehicle. Once the details are picked out and the transfers are dry, paint the tank with a gloss varnish. Vallejo Model Colour Gloss Varnish is perfect for this, and you can apply it either by hand or by spraying. It’s important to leave the tank to dry for at least 12 hours, for the varnish to full harden, in fact I’d recommend leaving it a day or two though before starting the fun stuff.

 

Step 4 – Dunk in water & cover in salt

Singleton Whitewash (4)

Yes you read that right. No I didn’t copy and paste it from a roast potato recipe. We’re going to be using the salt to protect the base coat areas and get the characteristic streaky, chipped look to the white paint. To do this, get two bowls, one full of water, one full of salt. Dip the tank in the water and whilst it’s still wet sprinkle salt over it, and also rub pinches of salt along the edges, areas of wear, upper surfaces, anywhere you would like the base colour to be showing through. The more salt you apply, the more battered and worn your tank will look. I also use blue tac to mask any transfers at this stage too.

 

Step 5 – Paint White. Leave for about 20 minutes then use a tooth brush to scrub off the salt

Singleton Whitewash (5)

We’re now going to be painting the white tank white! I recommend using an acrylic white paint, either Games Workshop, Army Painter or Vallejo, for example. You can apply the white with an airbrush, paintbrush or packing foam from a blister pack dabbed on. You will want the paint to be fairly thin, but not as thin as a wash. Don’t use an aerosol spray though as the paint hardens very quickly, and is very opaque so doesn’t give the streaky finish seen on most winter whitewash.

Advertisement

Give the white paint enough time to become touch dry, usually around 20-30 minutes with an acrylic paint, and then use an old tooth brush or old paint brush to scrub the salt off. Once you have as much of the salt off as you can, wet the brush and remove the last few pieces of salt. Remove the blue tac over any transfers too. At this stage you should be starting to have a very nice looking tank! I strongly recommend re glossing the tank, ready for finishing the weathering…

.

Step 6 – Paint a wash on

Singleton Whitewash (6)

To add some depth and definition to your model, paint a wash into the recesses of the model. The gloss varnish will help the wash to flow better and will make it easier to remove any excess with a cotton bud. I make my own using artists oils, but Army Painter inks, Games Workshop Shades, and Vallejo Sepia ink are all good options too.

 

Step 7 – Apply dirt/snow

Singleton Whitewash (7)

Nearly done! At this stage you may want to add more mud or compacted snow to the vehicle, especially around the track suspension and lower part of the vehicle. My favourite way to apply mud is to use Vallejo Texture Paint, Dark Earth. Paint this thickly onto anywhere you want to be muddy, then whilst the paint is still wet use a finger tip to wipe the paint off again. Do not lick your fingers testing to see if it tastes chocolaty. I have already conducted this research and it doesn’t…

To add snow, mix baking soda with either gloss varnish, or preferably Vallejo Water effect, until it becomes a past and use a cocktail stick to apply this to tracks, wheels, any where snow may congregate. Remember though that the back half of the tank is usually all engine and warm enough that the snow would melt, and that snow in all but the deepest recesses would be shaken off by the motion of the vehicle.

Singleton Whitewash (12)
Singleton Whitewash (11)
Singleton Whitewash (10)
Singleton Whitewash (9)
Singleton Whitewash (8)

With that, we’re done! You can play around with adding details, more weathering oil stains etc, but this will give you a great looking tank without too much difficulty.

Advertisement

Don’t forget to show us how you get on! – The Bolt Action Forum and Facebook page are a fantastic community of like-minded gamers and hobbyists – all keen to share their own projects, knowledge, and enthusiasm – so why not head over and take a look at what we’re all working on?

Andy Singleton

 

rp_WGB-WM-508-Tiger-IE-a.jpg

Tiger I AUSF.E

This technique is really handy as the “salt trick” can be used in a ton of different weathering effects like rust or battle damage. Great stuff from Warlord Games!

 

Who knew Winter Whitewashing had that much in common with roasting a potato!

Avatar
Author:
Advertisement
  • Warlord: Bolt Action "Empires In Flames"